C-SCOPE SG-V Instruction Manual download pdf (Page 4)

Precision Pipe & Cable Locator

Read Manual

Warning

C.SCOPEInter national Ltd

KingsnorthTechnology Park

WottonRoad

AshfordKent TN23 6LN

UnitedKingdom

Tel.+44 (0)1233 629181

Fax+44 (0)1233 645897

[email protected]

cscopelocators.com

Digital Display

with automatic backlight

Detachable Loudspeaker

On/ Off Switch

Sensitivity Control

4 Position Mode Switch

P: Power

R: Radio

G/T: Generator/ Transmitter

A: All Scan

Battery Compartment

Replaceable Wear Foot

CXL DXL MXL Locator Features

The C.Scope CXL, DXL and MXL Locators are Pipe and Cable Locators that can

provide precise information about the position and depth (DXL and MXL only)

of buried services. The combination of locating modes ensures buried services

are detected quickly and reliably.

TRACING

1. Carefully follow the direction of the signal always holding the Locator at right angles

to the line of the signal. Constantly move the Locator back and forth across the service

as shown in the diagram above to be sure of still being over the peak signal.

2. Stop and mark the position of the signal at regular intervals.As more marks are recorded

the precise direction of the service will become more apparent.

CAUTION

This Locator will find most services that radiate a detectable field.There may be some

services that do not radiate and cannot be found. Once a service is located always

check for others nearby.Multiple services in close proximity can affect the apparent

location of these services.

BATTERYCHECK

Switch the Locator on by pulling up on the On/Offtrigger

under the handle. Check for audible tone and the battery

level indicator in the bottom left hand corner of the display.

Replace batteries if necessary.

Do not leave discharged batteries in the equipment.

WARNING Do not change batteries in confined spaces where gas may be present.

SEARCHING IN GENERATOR(G) MODE

The search pattern used to find the Generator signal is slightly differentto that used

on Power,Radio or

All

Scan Modes.

DIRECT CONNECTION

1. Move a few paces away from where the Generator has been connected to the

service.Turn the Mode Switch to Generator Mode (G) and hold the Locator so that

the side is facing towards the Generator.

2.Adjust the Sensitivity so that the Locator is just showing

a visual response and emitting an audible response.

3. Walkin a COMPLETE circle around the connection

point trying to keep the same distance from this point

at all times. When a signal is detected, ‘pinpoint’that

signal as shown in the ‘Pinpointing’section above.

4. Having pinpointed the first signal, do NOTre adjust

the Sensitivity Control but continue with the circle to

see if any other signals are detected.

INDUCTION

Searching in induction mode is the same as for direct connection

except that the search is in a straight line across the end of the

Generator and at least 10 metres away.

SEARCHING IN POWER (P), RADIO (R)AND ALL SCAN (AS) MODES

1.Turn the Mode Switch to the appropriate mode.

2. Hold in the On/Offtrigger. The Locator should emit the audible battery test tone

and the digital display should come on. Check the battery level indicator to confirm

the batteries are usable.

3. Rotate the Sensitivity Control fully clockwise to maximum

setting as indicated by the arrow on the control.

4. Carry out the search using a grid pattern as shown

in the diagram. Walkslowly and keep the Locator

upright at all times and stationary by your side.

5.As you approach the area in which there

is a signal the Locator will emit an audible

response and show a visual response

on the display.

PINPOINTING

1. Walkthrough the area of the signal

response. If the visual response goes up

offthe scale reduce the sensitivity slightly.

2.The width of the signal response will

shrink as the sensitivity is reduced. Once

it is reduced enough then a peak response

will be seen on the display as the Locator

is moved back and forth over the service.

3. Mark this peak response position.

DEPTH MEASUREMENT WITHA GENERATOR

The Generator should be set to ‘Continuous’and is best in Connected Mode.

2. Set the Locator to Generator Mode. Rest the Locator on the ground above andAT RIGHT

ANGLESTO the line of the service.

3. Press and hold down the depth button.The depth will be shown in metres.

DEPTH MEASUREMENT WITHA SONDE

Carefully pinpoint the EXACTposition of the Sonde.

2. Rest the Locator on the ground above and IN LINE WITH the Sonde.

3. Push the depth buttonTWICE and hold on the second push. ‘SONDE’ will flash on the

display and the depth will then be shown in metres.

Read Manual

Warning

DepthMeasuring

CableAvoidanceTool

Basic Operating Instructions

Read the Instruction Manual Before Use

OK Replace

10 metres

C.SCOPEInter national Ltd

KingsnorthTechnology Park

WottonRoad

AshfordKent TN23 6LN

UnitedKingdom

Tel.+44 (0)1233 629181

Fax+44 (0)1233 645897

[email protected]

cscopelocators.com

5 0 6 0 0 8 6 3 5 0 6 7 8

TRACING

1. Carefully follow the direction of the signal always holding the Locator at right angles

to the line of the signal. Constantly move the Locator back and forth across the service

as shown in the diagram above to be sure of still being over the peak signal.

2. Stop and mark the position of the signal at regular intervals.As more marks

are recorded the precise direction of the service will become more apparent.

CAUTION

This Locator will find most services that radiate a detectable field.There may be some

services that do not radiate and cannot be found. Once a service is located always

check for others nearby.Multiple services in close proximity can affect the apparent

location of these services.

BATTERYCHECK

Switch the Locator on by pulling up on the On/Offtrigger

under the handle. Check for audible tone and the battery

level indicator in the bottom left hand corner of the display.

Replace batteries if necessary.

Do not leave discharged batteries in the equipment.

WARNING Do not change batteries in confined spaces where gas may be present.

SEARCHING IN GENERATOR(G) MODE

The search pattern used to find the Generator signal is slightly differentto that used

on Power,Radio or

All

Scan Modes.

DIRECT CONNECTION

1. Move a few paces away from where the Generator has been connected to the

service.Turn the Mode Switch to Generator Mode (G) and hold the Locator so that

the side is facing towards the Generator.

2.Adjust the Sensitivity so that the Locator is just showing

a visual response and emitting an audible response.

3. Walkin a COMPLETE circle around the

connection point trying to keep the same distance

from this point at all times. When a signal is

detected, ‘pinpoint’that signal as shown in the

‘Pinpointing’section above.

4. Having pinpointed the first signal, do NOT

readjust the Sensitivity Control but continue with

the circle to see if any other signals are detected.

INDUCTION

Searching in induction mode is the same as for

direct connection except that the search is in a

straight line across the end of the Generator

and at least 10 metres away.

SEARCHING IN POWER (P), RADIO (R)AND ALL SCAN (AS) MODES

1.Turn the Mode Switch to the appropriate mode.

2. Hold in the On/Offtrigger. The Locator should emit the audible battery test tone

and the digital display should come on. Check the battery level indicator to confirm

the batteries are usable.

3. Rotate the Sensitivity Control fully clockwise to maximum

setting as indicated by the arrow on the control.

4. Carry out the search using a grid pattern

as shown in the diagram. Walkslowly

and keep the Locator upright at all

times and stationary by your side.

5.As you approach the area in which

there is a signal the Locator will emit

an audible response and show a visual

response on the display.

PINPOINTING

1. Walkthrough the area of the signal

response. If the visual response goes up

offthe scale reduce the sensitivity slightly.

2.The width of the signal response will

shrink as the sensitivity is reduced. Once

it is reduced enough then a peak response

will be seen on the display as the Locator

is moved back and forth over the service.

3. Mark this peak response position.

Read Manual

CableAvoidanceTool

Warning

OK Replace

10 metres

Basic Operating Instructions

Read the Instruction Manual Before Use

C.SCOPEInter national Ltd

KingsnorthTechnology Park

WottonRoad

AshfordKent TN23 6LN

UnitedKingdom

Tel.+44 (0)1233 629181

Fax+44 (0)1233 645897

[email protected]

cscopelocators.com

5 0 6 0 0 8 6 3 5 0 6 6 1

1 2 3 4 5 6 7 8 9 ... 55 56

Comments to this Manuals

No comments

C-SCOPE SG-V Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools C-SCOPE SG-V